Garage door drive interface, KNX

Hormann garage door remote control unit as part of the Smart Home system via a KNX bus with the ability to connect various remote garage gas sensors. It is installed on a DIN rail, wall, ceiling.

Description
Specification
Documents
Release

A remote control unit for Hormann garage door drives via a KNX bus with the ability to connect various remote sensors for garage gas pollution and monitoring exceeding limit values. It is installed on a DIN rail, wall, ceiling.

Compatible Hörmann drives:

Drive	Note	The position of the “Series” switch
ProMatic 4 / SupraMatic 4		4
Liftronic 700-2 / Liftronic 800-2		4
ProMatic 3 / Liftronic 500		not supported
SupraMatic 3 / SupraMatic HT3 ¹	The serial number ends in “D”, “E”, “F”	3
LineaMatic / LineaMatic 2
RotaMatic / RotaMatic 2
VersaMatic
WA 300 R S4 / WA 300 S4

Specifications

Transmitting the gate status to the KNX bus
Opening, closing, switching to ventilation mode
Control of gates that are forgotten for a long time in the open position
Sound notification of various emergency situations
Connection of up to 2 garage gas sensors (exhaust gases, methane, propane, carbon dioxide)
Monitoring of excess gas content in the room (if sensors are connected)
The possibility of switching to ventilation mode when the maximum gas concentration is reached (if there is an appropriate sensor).
The function of cold reset of the 4th series drives in case of loss of communication (for example, after downloading the ETS application)
Accessories for garage door drives: Hörmann

Accessories for garage door drives: Hörmann:

Article number	HMN-F0100-1
The KNX interface
Specification	TP-256
Connecting to the bus	The WAGO connector 243-211
The device is powered	by the KNX bus, from the gate drive
KNX bus consumption (29V DC)	<2mA
Consumption from gate drive (24 V DC)	<50mA
Physical characteristics
Operating temperature range	from 0 to +45°C
Humidity during operation	from 5 to 95% (non-condensing)
Fire resistance class	UL94 V0 (does not support gorenje)
Degree of protection of the housing	IP20, in a clean environment
DIN rail mounting type	(EN50022) in an electrical cabinet
Size	37x91x61mm (37x107x61)
Weight	100g
Configuration program	ETS 5/6 (RU/EN)

Device description: Datasheet-HMN-F0100-1-RU.PDF

Instructions: Manual-HMN-F0100-1-RU.PDF

Application program ETS5/6 EN/RUS. Version 1.2 Download

Visio Element Library Download

Connection diagram of sensors and interface Download

Rejection letter

KNX 8-ch binary input/output and temperature sensors DIN

Universal module of 8 inputs/outputs, in a housing for mounting on a DIN rail.

Description
Specification
Files

A module of binary inputs/outputs, inputs for temperature, humidity or light sensors in a housing for installation in a shield on a DIN rail. The module size is 2DIN (37mm).

Up to 8 binary inputs
Short/long press, dimming, Curtain control
Switch mode
Pulse counter
Activating scenes
Curtain management
Up to 8 LED outputs
Up to 8 SSR control outputs for the heating valve relay
Up to 8 NTC temperature sensors
Up to 8 digital sensors for temperature, humidity, and light
8 thermostats
20 logic modules with a choice of one of 31 functions for each
Powered by the KNX bus

Article number	BIN-K0800-1
General parameters
The device is powered	by the KNX bus
Number of inputs	Up to 8
Number of outputs (for LED up to 2mA each)	Up to 8
Maximum length of the NTC temperature sensor cable to be connected	30m
Maximum length of the connected digital sensor cable	100m
The cross-section of the connected wire	Up to 1mm²
Operating temperature range	from 0 to + 45°C
Humidity during operation	from 5 to 95% (non-condensing)
Degree of protection of the housing	IP 20, in a clean environment
DIN rail mounting type	(EN50022) in an electrical cabinet
Size	37х91х61mm
Weight	85g
Material	ABS UL94V0
The KNX interface
Specification	TP-256
Configuration program	ETS 5.7 and higher
Connection	Standard EIB Connector (WAGO 243-211)
KNX bus consumption (29V DC)	< 5 mA , < 150 mW
Accessories
NTC temperature sensor (thin cable), 1m	NTC-S0101-1
NTC temperature sensor, 3m cable	NTC-S0102-1
Датчик температуры NTC, гильза 5*30мм , кабель 3м	NTC-S0103-1
NTC temperature sensor, sleeve 530mm , 3m cable NTC-S0103-1 Digital temperature sensor, sleeve 530mm, 3m cable	OWR-S0101-1

Device description : Datasheet-BIN-K0800-1-RU

Application program ETS5/6 ver 1.6 EN/RUS download

Application program ETS5/6 ver 1.7 EN/RUS download

Elements set Visio download

Binary input/output 4 ch. KNX

KNX interface for 4 binary inputs/outputs in a compact package for installation in a mounting box

Description
Specifications
Files

Binary I/O module in a compact package for installation in a mounting box.

Up to 4 binary inputs

Short/long press, dimming
Switch mode
Pulse counter
Activating scenes

Curtain management
Up to 4 LED outputs
10 logic modules with a choice of one of 31 functions for each
Powered by the KNX bus

Article number	BIN-F0400-1
General parameters
Device power supply	By KNX
Количество входов	Up to 4
Number of outputs (for LED up to 2mA each)	Up to 4
Connection type	Two 3-wire connectors with 15cm, 25cm cable
Humidity during operation	5…95%
Degree of protection of the housing	IP 20
Mounting type	Degree of protection of the housing
Size without knx terminal	42 х 33 х 9,5mm
Weight	20g
Housing material	ABS UL94V0
KNX interface
Specification	TP-256
Configuration program	ETS 5.7 and high
Connection	Standard connector EIB (WAGO 243-211)
KNX bus consumption (29V DC)	< 5 mA , < 150 mW

Device Description: Datasheet-BIN-F0400-1-RU.PDF

User’s Guide: Manual-BIN-F0400-1-RU.pdf

Logical modules: Manual-Logicmodules-ru.pdf

Application program ETS5/6 EN/RUS download

Examples of the organization of algorithms on logic modules download

The Library of Elements Visio download

Housing material: ABS UL94V0

KNX binary inputs module

KNX module of 4-x binary inputs/outputs, temperature sensors and a leak sensor in a compact housing

€ 140

Buy

Description
Specifications
Documentation

KNX binary input/output module, temperature sensors and leak sensor in a compact package for installation in a mounting box

Up to 8 binary inputs
- Short/long press, dimming
- Switch mode
- Pulse counter
- Activating scenes
Curtain management
Up to 6 LED outputs
Up to 4 NTC temperature sensors
Up to 2 loops with temperature sensors such as DS18S20, DS18B20 (up to 4 sensors on each loop, with the function of averaging, maximum, minimum values)
Connector for connecting a leak sensor of the “Neptune” type.
4 thermostats
Powered by KNX bus

Device model	BIN-F1300-1
Universal channels
Number of inputs/outputs	8 pcs
Input/output current	2mA
Input/output voltage	3,3V
Connection type	5-wire connector with cable (20 cm), 2 pcs.
The maximum length of the connected cable	30m
The cross section of the connected wire	до 1mm²
Input of the “Neptune” type leak sensor	1
The maximum current consumption by the leak sensor	2mA
KNX Interface
Specification	TP-256
Configuration program	ETS 5/6 (RU, EN)
Connection	connector WAGO 234-211
Powered by	KNX bus
KNX bus consumption (29V DC)	<5mA
Operating temperature range	0…+45°C
Humidity during operation	5..95% (non-condensing)
Enclosure protection	IP20, clean environment
Flammability class (1,5 mm)	UL94 V0
Type of installation	junction box
Size	42х33х12mm
Weight	20g

Basic Guide: Datasheet-BIN-F0801-1-EN.PDF

Basic Manual: Manual-BIN-F0801-1-EN.PDF

Thermostat: Manual-Thermostat-en.pdf

Logic modules: Manual-Logicmodules-en.pdf

Application program ETS5/6 EN/RUS Download

Examples of the organization of algorithms on logic modules Download

Housing material: ABS UL94V0

Declaration of Conformity ЕАС

Rejection letter

KNX relay/blind/shutters Actuator 16 output

Universal 16-channel KNX relay actuator with the possibility of using as a curtain/blinds actuator. Powerful relays capable of switching high starting currents are used as relays. Manual control. Selective control blocking. Convenient selection of any combination of channel pairs to control curtains/blinds. Thanks to the bistable relays, the module is powered via the KNX bus.

Relay 16-channel KNX actuator with manual control. It contains bistable relays designed for an operating current of 16A and high starting currents. It is installed on a DIN rail. The width of the device is 8 DIN.

€485

On stock

Buy

Description
Specifications
Files

Universal 16 channel KNX relay actuator with the possibility of using as a curtain/blinds actuator. Powerful relays capable of switching high starting currents are used as relays. Manual control. Selective control blocking. Convenient selection of any combination of channel pairs to control curtains/blinds.

Powered by KNX bus
16 independent high-power load control channels or 8 curtain/louver control channels
Indication of the status of each channel
Manual switching of each channel
Saving the state in case of a KNX power failure
Channel blocking in manual control mode
Scenario-based automation
Semi-automatic calibration of curtain movement time
Accounting for the phase of smooth acceleration of curtains

Device function				Building automation and home automation
External power supply				No required
Operating temperature				0°C .. +55°C
Storage temperature				-20°C .. +55°C
Humidity during operation				5..95%
Storage humidity				5..95%
Flammability class (1,5 mm)				UL94 V0
Additional Features				Class B
Protection class/Overvoltage category				II/III (4000V)
Operation mode				Continuous
Type of device action				Type 1
Working time under load				Long
Degree of protection/Degree of contamination				IP20/2, in a clean environment
Installation				A separate device is mounted on a DIN rail (EN50022) in an electrical cabinet
A minimum gap between the devices				not required
Response to a KNX power failure				Saving data according to parameterization
KNX Power recovery response				Data recovery according to parameterization
Indication of operating modes				The KNX programming indicator. In programming mode, the indicator lights up red.

Application program ETS5.7 / ETS6 (EN) – by request info@atrel.ru

Technical Specification (EN)

KNX relay/blind/shutters Actuator 8 outputs

Relay 8-channel KNX actuator with manual control. It contains bistable relays designed for an operating current of 16A and high starting currents. It is installed on a DIN rail.

€295

On stock

Buy

Description
Specifications
Files

universal 8-channel KNX relay actuator with the possibility of using as a curtain/blinds actuator. Powerful relays capable of switching high starting currents are used as relays. Manual control is possible. Selective control blocking. Convenient selection of any combination of channel pairs to control curtains/blinds. The module is powered via a KNX bus.

Powered by KNX bus
8 independent high-power load control channels or 4 curtain/louver control channels
Indication of the status of each channel
Manual switching of each channel
Saving the state in case of a KNX power failure
Channel blocking in manual control mode
Reception of real-time telegrams, automation based on it
Semi-automatic calibration of curtain movement time
Accounting for the phase of smooth acceleration of curtains

Device function	Building automation and home automation
External power supply	Not required
Operating temperature	0°C .. +55°C
Storage temperature	-20°C .. +55°C
Humidity during operation	5..95%
Storage humidity	5..95%
Flammability class (1,5 mm)	UL94 V0
Protection class/Overvoltage category	II/III (4000V)
Operation mode	Continuous
Working time under load	Long
Degree of protection/Degree of contamination	IP20/2, in a clean environment
Installation	A separate device is mounted on a DIN rail (EN 50022) in an electrical cabinet
A minimum gap between the devices	not required
KNX power failure response	Saving data according to parameterization
KNX Power recovery response	Data recovery according to parameterization
Indication of operating modes	The KNX programming indicator. In programming mode, the indicator lights up red.

Technical Specification (EN)

SMS Interface, KNX

A device for remote monitoring and control
of KNX devices by sending and receiving information messages via SMS channel.

€280

On stock

BUY

Description
Specifications
Documentation
Files

A device for remote monitoring and control of KNX devices by sending and receiving information messages via SMS channel.
• Sending and receiving messages to specified phone numbers (up to 10 numbers)
• Sending a message about a power failure in the KNX bus
• Periodic monitoring of the balance on the SIM card.
• Up to 50 types of outgoing information messages
• Up to 20 types of incoming SMS for device management – temperature setting, load on/off, etc.
• The ability to transmit a single numeric parameter (for example, temperature) in the template body
• Storing message templates and phone numbers in an end-user-friendly format on an SD card.
• Saving unsent messages in case they cannot be sent, and sending them after resuming communication.
• Sending real-time telegrams to the bus (according to GSM network data)
• The ability to connect an external GSM antenna

Device model	SMS-K2050-1
Universal channels
Frequency of sending messages when powered by the KNX bus	10/min
KNX Interface
Specification	TP-256
Configuration Program	ETS 5/6
Connection	Connector WAGO 234-211
Device power supply	Bus KNX
KNX bus consumption (29 V DC)	<12mA
Operating temperature range	от 0 до +45°C
Humidity during operation	от 5 до 95% (non-condensing)
Degree of protection of the housing	IP20, in a clean environment
Flammability class (1,5 mm)	UL94 V0
Type of installation	on a DIN rail (EN 50022) in an electric cabinet
Size	37x91x61mm (37x107x61 with external antenna)
Weight	50g

Datasheet-sms-k2050-1-en.pdf

Manual-sms-k2050-1-en.pdf

Application program ETS 5/6 EN/RUS on request info@atrel.ru

The program for editing the configuration file (Version 1.0.0.12 from 12/22/2022) download

Example of the microSD card configuration file of the smc.ini device on request info@atrel.ru